Difference between revisions of "Hardware/en"
From meteobridge
(Importing a new version from external source) |
(Updating to match new version of source page) |
||
Line 34: | Line 34: | ||
|MWR902AC | |MWR902AC | ||
|1.x | |1.x | ||
− | |Can be flashed via stock web interface | + | |Can be flashed via stock web interface. |
|- | |- | ||
|TP-Link | |TP-Link |
Revision as of 07:19, 3 February 2018
<languages />Meteobridge can be used with a variety of miniature consumer routers from TP-LINK, one from D-Link and one from ASUS, or you can by a Meteobridge PRO which comes on dedicated hardware. The devices from TP-Lin, D-Link and Asus are converted into a Meteobridge by flashing a new firmware. As always when you flash un-official firmware to a device you are voiding the manufacturers warranty. That means, when the device gets faulty later on, you can't reach out to TP-LINK, D-Link or ASUS for warranty. smartbedded UG, which owns the Meteobridge software, does also not provide any warranty on flashed device. As the routers are very cheap and risk of bricking the device is minimal, you don't have a significant financial exposure. However, you have to know, that you are converting the router into a Meteobridge at your own risk. If you don't want to take the risk, please buy a ready-made Meteobridge solution from one of the resellers or you go with a Meteobridge PRO.
Contents
Compatibility Overview
Over time new hardware revisions of devices originally supported by Meteobridge did show up. Some of those are no longer capable to be reflashed with a Meteobridge image some are. Table below does gives you an overview of supported devices and hardware versions.
Manufacturer | Model | HW Version | Remark on Meteobridge Compatibility |
TP-Link | MR3020 | 1.x | Can be flashed via stock web interface. |
TP-Link | MR3020 | 3.x | Can only be flashed via TFTP. Due to lack of working Mediatek Open Source WiFi drivers currently no WLAN operation possible. |
TP-Link | MR3040 | 1.x | Not supported. |
TP-Link | MR3040 | 2.x | Can be flashed via stock web interface. |
TP-Link | MWR902AC | 1.x | Can be flashed via stock web interface. |
TP-Link | MWR902AC | 3.x | Not supported. |
TP-Link | WR703N | up to 1.6 | Can be flashed via stock web interface (a bit complicated as it is in Chinese language). |
TP-Link | WR703N | 1.7 and above | Not supported. |
D-Link | DIR 505 | A1, A2 | Can be flashed via stock web interface. |
Asus | WL-330N3G | Some models can be flashed via a TFTP client. You cannot see from the outside if the device you have is supported. |
TP-LINK TL-WR902AC (version 1.x)
TL-WR902AC from TP-Link is a tiny WLAN router, which is world-wide available for around $50. Flashing the unit with Meteobridge firmware makes the router a Meteobridge. This router hardware comes with the following features:- 8 MB flash
- 64 MB RAM
- One LAN port
- Internal dual-band WLAN (only 2.4 GHz supported, no external antenna)
- USB 2.0 port
- A couple of activity LEDs (USB, LAN, WLAN)
- Illuminated button on the top
- Dimensions: 2.9 x 2.6 x 0.9 inch (74 x 67 x22 mm)
- Weight: 2.0 oz (58 g) without accessories
- Temperature: 0°C ~40°C operating (-40°C~70°C storage)
- Humidity: 10%~90% operating (5%~90% storage)
- Power Consumption: 2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from TP-Link
- Street price around $50
TP-LINK TL-MR3020 (version 1.x)
TL-MR3020 from TP-Link is a tiny WLAN router, which is word-wide available for less than $40. Flashing the unit with Meteobridge firmware makes the router a Meteobridge. This router hardware comes with the following features:- 4 MB flash
- 32 MB RAM
- One LAN port
- Internal WLAN (no external antenna)
- USB 2.0 only port (not capable of driving USB 1.x devices, will need a USB 2.0 Hub inbetween)
- A couple of activity LEDs (USB, LAN, WLAN)
- Illuminated button on the top
- Dimensions: 2.9 x 2.6 x 0.9 inch (74 x 67 x22 mm)
- Weight: 2.0 oz (58 g) without accessories
- Temperature: -10°C ~60°C operating (-40°C~80°C storage)
- Humidity: 10%~90% operating (5%~90% storage)
- Power Consumption: 1-2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from TP-Link
- Street price below $40
TP-LINK TL-MR3020v3 (version 3.x)
TL-MR3020v3 from TP-Link is an updated version of the legacy TL-MR3020 but with completely changed internals. Unfortunately, there is no Open Source WiFi driver available for the Mediatek 7628 chip. Therefore, Meteobridge cannot offer WiFi operation so far. On the positive side this platform has twice the RAM and Flash-ROM than the former TL-MR3020 models and does not need a USB hub to connect to USB 1.x devices. This router hardware comes with the following features:- 8 MB flash
- 64 MB RAM
- One LAN port
- Internal WLAN is not supported by Meteobridge
- USB 2.0 port
- A couple of activity LEDs (USB, LAN, WLAN)
- Illuminated button on the top
- Dimensions: 2.9 x 2.6 x 0.9 inch (74 x 67 x22 mm)
- Weight: 2.0 oz (58 g) without accessories
- Temperature: -10°C ~60°C operating (-40°C~80°C storage)
- Humidity: 10%~90% operating (5%~90% storage)
- Power Consumption: 1-2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from TP-Link
- Street price below $40
TP-LINK TL-WR703N (versions up to 1.6 only)
TL-WR703N from TP-Link is the little brother of TL-MR3020. While technical specs are nearly identical it comes with an even smaller form factor and less LEDs for signaling status. TP-LINK does sell WR703N just on the China market, but you can easily get one via ebay for less than $30. Router hardware comes with the following features:- 4 MB flash
- 32 MB RAM
- One LAN port
- Internal WLAN (no external antenna)
- USB 2.0 only port (not capable of driving USB 1.x devices, will need a USB 2.0 Hub inbetween)
- One activity LED
- Reset button behind a pinhole at the back
- Dimensions: 2.2 x 2.2 x 0.7 inch (57 x 57 x 18 mm)
- Weight: 1.3 oz (36 g) without accessories
- Temperature: -10°C~60°C operating (-40°C~80°C storage)
- Humidity: 10%~90% operating (5%~90% storage)
- Power Consumption: 1 watts
- Certificates: no indication of CE, FCC, RoHS
- only available for China market from TP-Link, but easy to get world-wide via China-based ebay sellers
- Street price: below $30
ASUS WL-330N3G
WARNING: newest version of this device does not allow to be flashed with Meteobridge firmware. You can't tell from the outside if a specific WL-330N3G router is part of this new, blocking production batch or an older version that can be updated fine. Therefore, it is no longer recommended to buy this hardware, when you want to flash it to become a Meteobridge. We will continue to support successfully flashed "old" versions.
This tiny router from ASUS has similar specs like the ones from TP-Link. Flashing the unit is a bit more complicated (cannot be done via web interface, needs TFTP in a prepared LAN) but it can handle USB 1.x and USB 2.0 devices without need for an additional USB hub. Please do not confuse this router with its predecessor WL-330N, which is not suitable for Meteobridge.- 4 MB flash
- 32 MB RAM
- One LAN port
- Internal WLAN (no external antenna)
- USB 2.0 port (capable of driving USB 1.x and USB 2.0 devices)
- A couple of activity LEDs (Power, USB, LAN, WLAN)
- One button on the top and a non-functional reset button behind a larger pin hole at the bottom
- Dimensions: 90 x 38.9 x 12.8 mm (LxWxH)
- Weight: 1.3 oz (35 g) without accessories
- Power Consumption: abt. 1-2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from ASUS
- Street price: depends on region, cheaper in Europe/Asia (30 Euro), more expansive in the US ($50)
D-Link DIR-505
DIR-505 from D-Link is a tiny WLAN router, which is word-wide available for less than $40. Flashing the unit with Meteobridge firmware makes the router a Meteobridge. Meteobridge firmware is tested with DIR-505 A1 and A2 models. This router hardware comes with the following features:- 8 MB flash
- 64 MB RAM
- One LAN port
- Internal WLAN (no external antenna)
- USB 2.0 only port(not capable of driving USB 1.x devices, will need a USB 2.0 Hub inbetween)
- One activity LEDs
- User accessable utton on one of the sides
- reset button at the USB/LAN connector panel behing a pinhole
- Dimensions: 2.68 x 1.65 x 2 inch (68 x 42 x 51 mm)
- Weight: 3.67 oz (104 g) without accessories
- Temperature: 0°C ~ 40°C operating
- Humidity: 0%~90% operating (non-condesing)
- Power Consumption: 1-2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from D-Link
- Street price below $40
TP-LINK TL-MR3040 (version 2.x)
TL-MR3040 from TP-Link is a tiny WLAN router, which is word-wide available for less than $40. Flashing the unit with Meteobridge firmware makes the router a Meteobridge. Meteobridge firmware is tested with currently sold TL-MR3040 which are version 2.x. This router hardware comes with the following features:- 4 MB flash
- 32 MB RAM
- One LAN port
- Internal WLAN (no external antenna)
- USB 2.0 only port (not capable of driving USB 1.x devices, will need a USB 2.0 Hub inbetween)
- A couple of activity LEDs (USB, LAN, WLAN)
- Reset button behind pin hole near USB port
- Dimensions: 3.9 x 2.4 x 0.6 inch (100 x 62 x 16 mm)
- Weight: 3.3 oz (94 g) without accessories
- Temperature: -10°C ~60°C operating
- Humidity: 10%~90% operating (no condensing)
- internal 2000mAh rechargeable battery
- Power Consumption: 1-2 watts
- Certificates: CE, FCC, RoHS
- As a consumer router world-wide available from TP-Link
- Street price below $40
Meteobridge PRO
Meteobridge PRO is specialized hardware for Meteobridge. You can only buy it fully installed with SW and license and yes, it is more expansive then reflashing one of the miniature plastic routers above. But it also offers much more:- 16 MB flash
- 64 MB RAM
- One LAN port
- Internal WLAN with external RPSMA antenna
- 2 external USB 2.0 ports that can also handle USB 1.x devices
- Internal 8 GB USB storage
- optional: Internal RF receiver (Meteostick) to directly read out Davis ISS RF data
- LEDs for RF reception, network traffic, data storage, system status
- 128x64 graphical OLED (black/white)
- Internal sensors for temperature, humidity, pressure, voltage, power
- Power Consumption: 1-2 watts
- Reset button behind pin hole on front panel
- Dimensions: 57 x 95 x 27 mm
- Weight: 130 g with antennas, without accessories
- Temperature: -10°C ~ 60°C operating
- Humidity: 10%~90% operating (no condensing)
- Certification: CE, IC, FCC, RoHS
- International power supply