Difference between revisions of ":Getting Started/30/en"

From meteobridge
Jump to: navigation, search
(Neue Version von externer Quelle importiert)
(Importing a new version from external source)
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 
==Flashing Meteobridge Firmware to DIR-505==
 
==Flashing Meteobridge Firmware to DIR-505==
−
D-Link DIR-505 can be flashed most easily by the build in "Router Recovery Mode". To get there simply keep the reset button behing the pin hole pressed with the leg of a paper clip until the red led starts flashing slowly. This indicates that DIR-505 is now located at static IP 192.168.0.1 and is ready to upload a new firware. Configure your browsing PC to an IP in the same class-c subnet (192.168.0.123, for example) and browse to 192.168.0.1 and start screen displayed below (on the left) will appear. Web page offered by the router in recovery mode is a bit picky regarding browsers. Safari browser on Mac OS-X does work flawlessly, some other browsers on a Windows environments are reported to have problems. So you might have to try a bit until you have found a browser that can access the routers web content. When your browser don't reach the completed status (picture on the right) the flashing has not be done.
+
D-Link DIR-505 provides a "Router Recovery Mode", but firmware update through this does not work with todays browsers. Therefore, it is recommended to use the firmware update function of the DIR-505's stock firmware. This is done in a few simple steps.
 +
* Download Meteobridge firmware to your Laptop: [http://www.meteohub.de/files/meteobridge-dir-505-v1.3.bin meteobridge-dir-505-v1.3.bin] (or [http://www.meteohub.de/files/meteobridge-dir-505l-v1.3.bin meteobridge-dir-505l-v1.3.bin] if you have a DIR-505L)
 +
* Set mode switch of DIR-505 to "Router/AP".
 +
* Power-on DIR-505.
 +
* Wait until LED switches to green.
 +
* Connect your laptop with the WLAN the DIR-505 has setup. SSID and passphrase is on a separate card in the box the DIR-505 came with.
 +
* Start browser on your laptop and direct to "http://192.168.0.1".
 +
* Cancel internet setup dialog provided by stock firmware.
 +
* Enter as user "admin" without password.
 +
* Select "maintenance" tab from the horizontal menu.
 +
* Select "firmware" tab from the vertical menu.
 +
* Select downloaded Meteobridge firmware in "firmware upgrade" section and press upload button (picture on the left).
 +
* DIR-505 checks if firmware is compatible and starts upgrading (picture on the right). When done DIR-505 reboots as a Meteobridge.

Latest revision as of 16:38, 31 January 2015

Flashing Meteobridge Firmware to DIR-505

D-Link DIR-505 provides a "Router Recovery Mode", but firmware update through this does not work with todays browsers. Therefore, it is recommended to use the firmware update function of the DIR-505's stock firmware. This is done in a few simple steps.

  • Download Meteobridge firmware to your Laptop: meteobridge-dir-505-v1.3.bin (or meteobridge-dir-505l-v1.3.bin if you have a DIR-505L)
  • Set mode switch of DIR-505 to "Router/AP".
  • Power-on DIR-505.
  • Wait until LED switches to green.
  • Connect your laptop with the WLAN the DIR-505 has setup. SSID and passphrase is on a separate card in the box the DIR-505 came with.
  • Start browser on your laptop and direct to "http://192.168.0.1".
  • Cancel internet setup dialog provided by stock firmware.
  • Enter as user "admin" without password.
  • Select "maintenance" tab from the horizontal menu.
  • Select "firmware" tab from the vertical menu.
  • Select downloaded Meteobridge firmware in "firmware upgrade" section and press upload button (picture on the left).
  • DIR-505 checks if firmware is compatible and starts upgrading (picture on the right). When done DIR-505 reboots as a Meteobridge.
Retrieved from "https://wiki.meteobridge.com/wiki/index.php?title=:Getting_Started/30/en&oldid=4203"